![]() It produces fantastic prints using the out of the box settings, and we didn't have any issues with stringing or other print defects across a wide range of test prints. It rarely disappoints and is a strong yet dependable printer that will win you over to Creality's side. With the Ender-5 S1, Creality's Ender series maintains its strong reputation for producing high-quality printers. There was also little to no stringing on the prints, which is one of the benefits of using a direct drive extruder. Because of the dual part cooling duct, there were no overhang issues. These models were sliced using the standard 120mm/s profile and turned out beautifully. A small rabbit, a lucky cat, and a benchy boat are among them. The first prints we have are the included test prints. We also printed a few times with the 250mm/s profile and in both cases we couldn't be happier with the results. Throughout our testing, we stuck to using the Creality slicer's standard profile of 120mm/s. Creality Ender 5 S1: Print Quality & speed There will also be an acrylic enclosure available for the Ender 5 S1, which will help with temperature-sensitive materials like ABS and add rigidity to the printer frame itself. This is in addition to all the necessary features, including the auto-level system and the inclusion of the 300 Celsius maximum temperature of the included all-metal heat break.Ĭreality also plans to integrate the Ender 5 S1 into the Creality Sonic Pad, giving users a Klipper firmware option that is easy to set up and calibrate. The Ender 5 S1 might be the ideal printer for all of your needs given the simplicity of the on-screen menu system, which is packed with all the options you need to calibrate and configure the printer to your printing needs. Supported filaments: PLA, PETG, ABS, TPU, PC, ASA, HIPS Levelling: Manual + CR Touch Auto-levellingĬontrol panel: 4.3-inch color touch screen ![]() ![]() You can also buy an optional acrylic enclosure that will be available around launch, and there are plans to integrate the Ender 5 S1 into the Creality Sonic Pad, giving users a Klipper firmware option that is easy to setup and calibrate with the Sonic pad. The included SD card has three test prints to choose from once ready. Once complete, the printer will home the bed and you are ready to print (once you have loaded your filament of choice). The printer will go through the levelling process, checking several points on the bed. The final step, once the bed has been manually levelled, is to click on the Auto.LVL tab and click on Start. After you've set the offset, adjust the bed by clicking on the four corners and manually levelling each corner with the knobs. Once the bed is in the top position, adjust the offset by clicking the up and down arrows until the nozzle just grabs the paper. On the Aux.LVL screen, first click on the home icon on the right side. Once the printer has been assembled, all that remains is to plug it in, turn it on, and begin by accessing the settings menu and levelling method. Finally, double-check the voltage on the power supply to ensure it is set to the correct voltage for the country you live in. Each plug is labeled, making the final step simple. Install the two braces on the bottom rear of the printer frame, noting the R and L on the braces to determine which side they are installed on.Īll that remains is to install the spool holder on the right side, the Bowden extruder on the filament run out sensor and the direct drive, and finally to connect all the cables to the appropriate plugs. As with the other parts of the assembly, use the supplied M5x30 screws to secure the Z-axis to the frame and ensure that everything is tight. When you're ready to install the printing platform and Z-axis assembly, you might need a helping hand to tilt the printer frame forward to make room for the Z-axis assembly. We install the printing platform support arms on the bottom of the bed after we secure it to the Z-Axis assembly. We used the foam from the box to support the print platform as we attached the bed to the Z-axis assembly. The following step is to prepare the print bed assembly for installation on the printer frame. After that, install the top assembly using eight of the same M5x25 screws, making sure everything is square and tight. The first step in the assembly process is to secure the four profiles to the printer's base with eight M5x25 screws, ensuring that the profiles are square and straight. Left and Right Platform Support Assembly's
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |